Glue

In this section you can find different sorts of Glue

  • ACTIVATOR SPRAY 300ML

    This spray shortens the setting time of all cyano-acrylate glues to a minimum. Also suitable for use with the new Foam-Speed glue
    SKU: RB-5018
    €9.50

    OUT OF STOCK

    Notify me when in stock

  • Black Double Sided Tape 20mm x1m, 3mm thick

    3mm Thick Black Double Sided Foam Tape 20mm x 1 Meter.  Excellent vibrations absorber. Glue on gyros, FBL units, and more.
    This is a strong, general purpose foam tape coated on both sides with an adhesive that will perform in both internal & external applications. The foam is a high quality polyolefin coated with a high tack acrylic adhesive.
    This tape has been designed as an economic solution for your adhesive foam tape requirements.

    SKU: BFT200
    €3.00

    IN STOCK
  • COLD METAL STICK (STEEL OR ALU)

    COLD METAL STICK (STEEL OR ALU)
    Working in tempratures of -30°C -- + 150°C. Curing time is 60min.
    Final resistance is + 50 kg/cm² (after 24 h.)

    SKU: Robbe5368
    €9.00

    IN STOCK 48H
  • Contacta Professional plastic glue (25g)

    Revell Contacta Professional' is for pin-point accurate bonding. The extra-fine hollow needle allows for micro-fine gluing of tiny details and clear part edges. This professional glue is available in tow sizes.

    SKU: REV-39604
    €3.90

    IN STOCK
  • DryFluids Extreme Gear Lube

    DryFluids Extreme Gear Lube 10ml

    High end lubricant for highly stressed gears in modelling applications.

    Specially suitable for gears of model helicopters, RC cars, trucks, model railways and servos. Also applicable for axles and bearing systems in any modelling application.

    Multistage lubricant system with long-term effects.

    A long-lasting lubrication effect is achieved using dry particles, sliding polymers and high end sliding fluids. It is extreme pressure-resistant and has an excellent adhesive force. DyrFluid has minimal dust and dirt adhesion.

    It includes a pinpoint dispenser and a separate fine cannula for a very precise application, as well as a fine hair paintbrush for surface applications.

    The very young German company DryFluids provides a revolutionary new lubrication technology for RC helicopter. While conventional lubricants are mostly based on oil or grease, DryFluid Extreme takes an entirely new approach buy using ceramic lubricant particles and micro-sized polymers that remain dry while ensuring full lubrication. A special adhesive component ensures that the lubricating particles stick to the surface that they are intended to lubricate. A fourth key ingredient is the fast evaporating liquid carrier that also ensures an almost unbelievable capillary action, allowing the lubrication particles to penetrate into even the smallest areas between gears and surfaces. The liquid carrier is formulated to dry within minutes of being applied, giving this revolutionary new product its name: DryFluid. The “Extreme” suffix indicates the environments this product is designed for. It can be used under extreme pressure, remain thermally stable at high temperatures while still delivering incomparable low friction for long term lubrication and dry run protection. Dry run protection is a special property of the new technology offered by DryFluid Extreme. Tiny ceramic particles act as a low-friction bearing between surfaces to protect them from wear. In addition, lubricating polymers reduce friction to offer a long-term protective effect.

    No Mess Lubrication:

    What’s so innovative about DryFluid Extreme is how quickly it changes from a liquid to a dry film. This unique feature enables it to provide extended lubrication without attracting dirt and dust, unlike conventional lubricants that leave a sticky residue that cakes up with grime over use. Less dirt and dust means even less abrasion, something that RC heli pilots have greatly appreciated over comprehensive life-cycle testing. While conventional oils and grease rub away with use, DryFluid Extreme remains dry and stuck to its applied surface and reduces operating temperature. Basically, anything that moves can be treated with DryFluid Extreme including RC model shafts, bearings, guides, ball-links and swash plates. Field tests have shown that the reduction of friction by DryFluid even extended the auto-rotation time considerably. (The few exceptions are Nitro engines and compression bearings, which require purpose-made lubricants and greases.)
    SKU: DFGL
    €13.90

    IN STOCK
  • DryFluids Extreme Heli

    DryFluids Extreme Heli Lube 10ml

    High end lubricant for joints, axles and bearings of RC Helicopters. It contains top-class lubricating components from the aviation and vehicle industry. It increases the speed through extreme low sliding friction. Dust and dirt repellent. Excellent long-term lubrication results. It includes a pinpoint dispenser and a separate fine cannula for a very precise application. Content 10 ml

    Multistage lubricant system with long-term effects.

    A long-lasting lubrication effect is achieved using dry particles, sliding polymers and high end sliding fluids. It is extreme pressure-resistant and has an excellent adhesive force. DyrFluid has minimal dust and dirt adhesion.

    It includes a pinpoint dispenser and a separate fine cannula for a very precise application, as well as a fine hair paintbrush for surface applications.

    The very young German company DryFluids provides a revolutionary new lubrication technology for RC helicopter. While conventional lubricants are mostly based on oil or grease, DryFluid Extreme takes an entirely new approach buy using ceramic lubricant particles and micro-sized polymers that remain dry while ensuring full lubrication. A special adhesive component ensures that the lubricating particles stick to the surface that they are intended to lubricate. A fourth key ingredient is the fast evaporating liquid carrier that also ensures an almost unbelievable capillary action, allowing the lubrication particles to penetrate into even the smallest areas between gears and surfaces. The liquid carrier is formulated to dry within minutes of being applied, giving this revolutionary new product its name: DryFluid. The “Extreme” suffix indicates the environments this product is designed for. It can be used under extreme pressure, remain thermally stable at high temperatures while still delivering incomparable low friction for long term lubrication and dry run protection. Dry run protection is a special property of the new technology offered by DryFluid Extreme. Tiny ceramic particles act as a low-friction bearing between surfaces to protect them from wear. In addition, lubricating polymers reduce friction to offer a long-term protective effect.

    No Mess Lubrication:

    What’s so innovative about DryFluid Extreme is how quickly it changes from a liquid to a dry film. This unique feature enables it to provide extended lubrication without attracting dirt and dust, unlike conventional lubricants that leave a sticky residue that cakes up with grime over use. Less dirt and dust means even less abrasion, something that RC heli pilots have greatly appreciated over comprehensive life-cycle testing. While conventional oils and grease rub away with use, DryFluid Extreme remains dry and stuck to its applied surface and reduces operating temperature. Basically, anything that moves can be treated with DryFluid Extreme including RC model shafts, bearings, guides, ball-links and swash plates. Field tests have shown that the reduction of friction by DryFluid even extended the auto-rotation time considerably. (The few exceptions are Nitro engines and compression bearings, which require purpose-made lubricants and greases.)
     

    SKU: DFHELI
    €13.90

    IN STOCK
  • Epoxi Cement

    Tube of 56 gr, this cement is flexible, after the mix it is strong as steel.

    Use to repair Metal, Wood, plastic

    SKU: RCM16346
    €8.30

    IN STOCK
  • Filament Tape

    GLASS FILAMENT TAPE
    Economical filament tape is tough and strong. Contains glass yarn filaments for up to 300 lbs. in tensile strength.


    These adhesive tapes feature a longitudinal reinforcement consisting of glass fibre strips. The tape is very strong and has strong adhesive power. It is also extremely resistant to tearing.

    Roll of 50 meters, perfect to use on Shock flyers, and other airplanes as a hinges.

    Specification
    Width:25 mm
    Adhesive power:7.2 N / cm
    Tear strength:260 N / m

    SKU: RCM5371
    €8.00

    IN STOCK
  • FLEX ZAP

    High strength, shock resistant, moisture and solvent resistant

    Ideal for fibreglass, and cabon fibre

    Cures clear

    Sets in 30 seconds

    Works best on: Metal, Rubber, Pottery, Most plastics,

    Works best on: Aluminium, Ceramic, Fibreglass, Carbon fibre

    SKU: ZAPPT32
    €6.80

    LOW STOCK
  • Gyro Mounting Pads

    Fits All Gyros, servos and more !!

    These Futaba high quality Gyro and receiver mounting pads are double sided tape which is used to both securely hold the gyro in place but just as importantly act as a dampener between the frame and the gyro.
    This allows for shock absorption from the Helicopters natural vibration.
    Each pad is cushioned to help to eliminate vibration.

    3 PCS in set

    SKU: RCT0025
    €3.00
    €4.00

    IN STOCK
  • JB Weld

    Use J-B WELD as an adhesive, laminate, plug, filler, sealant, and electrical insulator. Squeeze out equal portions from the black and red tubes. Mix thoroughly. Clean surface to be bonded. Apply J-B WELD, and let it cure. That's all there is to it!J-B Weld is an amazing formula which once binds will produce an ever lasting strong bind which will hold tight and not come loose. Often used on mount pinions to a motor’s main shaft.The pinion will not slip or fall once J-B is applied. The formula is easy to apply and comes in two tubes. J-B weld is a must have in anyone’s tool box and has been proven to be the de-facto in cold soldering in many R/C hobbies including Radio Controlled Helicopters.

    SKU: RCTA-0061
    €12.50

    LOW STOCK
  • Kwik JB Weld

    Tensile strenght 2500 psi
    Resistant to constant temperature up to 150 c
    Cure in 4 minutes. Full strenght in 20 minutes
    Bonds metal, plastic, ceramic, wood, masonary
    Can be drilled, filled, sanded, machined, tapped and painted

    SKU: JB8276
    €9.50

    IN STOCK
  • LIQUID METAL 25ML

    LIQUID METAL 25ML
    SKU: Robbe5366
    €11.00

    IN STOCK
  • LOCTITE 648

    Loctite 648 high strength, good temperature resistance retainer this is an upgrade for loctite 243

    The ideal adhesive for gluing the shaft and hub. a single-component, removable anaerobic thread locking adhesive. Because Loctite 648 is formulated to be tolerant of oil and other contamination, fasteners can be used as received with no additional cleaning or preparation required before the thread locker is applied.Your benefits Increased temperature resistance Ideal for retaining of parts with a clearance or interference fit, i.e. retaining bushes, bearings, seals, fans, and liners

    Technical Data
    Diametrical clearance: Up to 0.15 mm
    Service temperature range: -55°C to +175°C
    Tensile shear strength: >25 N/mm²
    Fixture time on steel: 3 min.

    SKU: S1307
    €8.60
    €8.90

    IN STOCK
  • POWERZIP STRIP

    POWERZIP strip, 16mm wide, 1meter long

    Power tape, holding power is up to 50 kg!!, Double face transparent silicone tape ( red cover), excellent for installation of wires, wood, fiber, Gyro , Receiver and more..

    Its suitable for internal & external use it offers high adhesion to a wide variety of surfaces. It has superior 'wetting out' properties which increase the bonded surface area increasing the strength of the bond. It has excellent ageing properties and is resistant to U.V. light, abrasion, corrosion & moisture.
    Service temperature is -30°c - +80°c (continuous)/ +130°c (shorterm).


    SKU: RB-5367
    €5.00

    IN STOCK
  • Ropoxi Glue 5min 2x100gr

    5-minute epoxy glue

    • 1:1 mixing ratio for ease of use.
    • The adhesive produces tough, high-strength joints in wood, metal and various plastics.
    • Approx. 5 minutes working time at 24°C.
    • Sets hard in about 10 minutes at 24°C.
    • Full cure in 2-3 hours at 24°C.
    SKU: RB-5070
    €13.99

    LOW STOCK
  • Ropoxi Glue 5min 2x50gr

    5-minute epoxy glue

    • 1:1 mixing ratio for ease of use.
    • The adhesive produces tough, high-strength joints in wood, metal and various plastics.
    • Approx. 5 minutes working time at 24°C.
    • Sets hard in about 10 minutes at 24°C.
    • Full cure in 2-3 hours at 24°C.
    SKU: RB-5066
    €9.50

    IN STOCK
  • Silicone Special 250 Sealant

    Silicone Special for High temp sealing.

    • Cold vulcanizing silicone rubber.
    • Permanently elastic silicone sealing
    • compound for engine and body.
    • For sealing of surfaces, gaps and
    • cracks on water pumps, oil sumps
    • radiators, crank cases etc.
    • Bridges large, uneven surfaces.
    • Gives a reliable seal, withstanding many years of vibration.
    • Excellent adhesive properties.
    • Will not drip, sag or become stringy.
    • Excellent chemical resistance.

    Skin formation after a few minutes,
    Temprature range : -50 -- 300c
    Package of 70ml

    SKU: Wurth890323
    €9.90

    IN STOCK
  • Slo-Zap CA-56gr

    Thick and strong for high-stress areas. Ideal for laminating and forming fillets.
    Allows you 30 seconds to position; cures in 60 sec.
    2-oz /56gr bottles

    SKU: ZAPPT33
    €14.90

    IN STOCK
  • UHU Por for Depron/EPP

    Special quick-setting adhesive for assembling rigid polystyrene foam (eg Styropor®), and in conjunction with other materials.
    The elastic adhesive film is colourless and waterproof.Materials:
    Rigid foam materials such as Styropor®, and in conjunction with other materials such as wood, paper, metal, ceramic, plaster, textiles and various plastics.
    Also highly suitable for sticking photosInstructions for useApply adhesive to both parts to be stuck together. Leave to dry. Once dry to the touch (after approx. 10 minutes), press together very firmly for a short time. Take care not to damage rigid foam material.

    SKU: SKU14430
    €7.00

    IN STOCK
  • Z-42 Blue Thread Locker

    Medium strength general purpose thread locker Locks threaded fasteners against vibration Perfect for use in helicopters and all RC cars Clean and dry parts for best results (removing grease, oil and dirt) Parts can be returned to service immediately in MOST CASES Thread locking compound comes in a Red bottle with a clear nozzle tip

    Comments:
    This bottle of glue will appear big in context to the glue. The reason being is the glue requires a large amount of oxygen or the glue will dry out. All one would need to do once you have the glue is shake the bottle and turn upside down, if the tip turns Blue then the glue is present. To some the bottle may appear empty.

    Application:
    * Please remove all grease, moisture glue and apply the adhensive to the surface to be adhered, (Not Plastic Bolts)
    * Wait for 1 ~ 10 minutes before exerting force to stabilize the adhensive grip.
    * Excessive glue may result in extended gluing time.
    * Seals Metal Parts Against Vibration, Parts Can Later Be Separated Using Hand Tools
    SKU: ZAPPT42
    €4.80

    IN STOCK
  • ZAP 30m EPOXY

    Uses:

    30 MINUTE Z-POXY is a premium high strength two part epoxy adhesive. The 30 minute cure time allows a greater working time and increased pot life. Vibration resistant and fuel proof, this epoxy is perfect for all types of hobbies and crafts. Use it on all fire wall and engine mount installations, its perfect for attaching bulkheads and formers in epoxy glass fuselages and boat hulls. It does not get brittle with age and its easy to mix, just combine equal parts by volume. Handy to have at home for all types of fix-it jobs, great to have in the shop for all types of wood working and furniture repair.

    Helpful Hints:

    30 MINUTE Z-POXY does fully cure in approximately 30 minutes, that means you will have about 15 minutes working time. To clean up any uncured or unmixed epoxy, use alcohol, isopropyl or methanol, either will work. Thinning of 30 MINUTE Z-POXY is possible in smaller ratios, thinning too much will alter the cured properties and may not produce an adequate bond. It is best to test the thinned epoxy, let it cure and adjust as need. Mix Z-POXY in a plastic cup or on a non porous surface like a piece flexible plastic. Only mix enough epoxy as needed, any excess epoxy cannot be saved after it has been mixed. Pot life and cure time will vary when the epoxy is thinned. Since epoxies cure by an exothermic chemical reaction, ( give off heat ) and heat can speed the cure of epoxy, mixing large amounts can shorten the pot life if not spread out right away. For a quick cure epoxy, use Z-POXY QUICK SET 5 MIN. FORMULA part numbers PT-37 and PT-38.

    PT-39
    8oz. (227.2ml) Z-POXY 30 Minute

    SKU: ZAPPT39
    €16.00

    IN STOCK
  • ZAP 5m EPOXY

    Uses:

    5 MINUTE Z-POXY is a premium high strength two part epoxy adhesive. Vibration resistant and fuel proof, this epoxy is perfect for all types of hobbies and crafts. Use it on all fire wall and engine mount installations, its perfect for attaching bulkheads and formers in epoxy glass fuselages and boat hulls. It does not get brittle with age and its easy to mix, just combine equal parts by volume. Handy to have at home for all types of fix-it jobs, great to have in the shop for all types of wood working and furniture repair.

    Helpful Hints:

    5 MINUTE Z-POXY does fully cure in approximately 5 minutes, that means you will have about 2 minutes working time. To clean up any uncured or unmixed epoxy, use alcohol, isopropyl or methanol, either will work. Thinning of 5 MINUTE Z-POXY is possible in smaller ratios, thinning too much will alter the cured properties and may not produce an adequate bond. It is best to test the thinned epoxy, let it cure and adjust as need. Mix Z-POXY in a plastic cup or on a non porous surface like a piece flexible plastic. Only mix enough epoxy as needed, any excess epoxy cannot be saved after it has been mixed. Pot life and cure time will vary when the epoxy is thinned. Since epoxies cure by an exothermic chemical reaction, ( give off heat ) and heat can speed the cure of epoxy, mixing large amounts can shorten the pot life if not spread out right away.

    PT-38
    8oz. (227.2ml) Z-POXY 5 Minute

    SKU: ZAPPT38
    €16.00

    IN STOCK
  • ZAP A GAP CA+ 1 OZ

    SUPERIOR GAP FILLING FORMULA
    liquid viscosity
    ALLOWS APPROXIMATELY 7 TO 10 SECONDS FOR PART POSITIONING


    Uses:

    ZAP-A-GAP CA+ Is the best selling instant glue in the world. The ability to bond virtually anything to anything with consistency unequalled by any other brand makes it the favorite adhesive across many varied disciplines. Widely used throughout the hobby industry, it is the absolute best and most consistent performing glue for model building and crafting. Some uses besides hobbies and crafts include; jewelry manufacturing and repair, taxidermy, pool cue tips, darts, archery, knife making, mold and pattern making, furniture refinishing and antique repair, auto detailing, dental molds and patterns, ceramic repair, and for fishing, fly line splicing and fly tying. For manufacturing, the ability to bond metal and / or plastic parts allows for fast simple fixturing and positioning for assembly or machining. Wood turners and manufactures of custom wood products appreciate the ability of ZAP-A-GAP CA+ to help save their projects by filling in and bonding cracks that often occur in expensive hard woods. Wood, plastic, metal, glass, ceramic, fabric, rubber, fiberglass, carbon fiber, or any combination of, ZAP-A-GAP CA+ can help solve many tough bonding problems.

    Helpful Hints:

    A little goes a long way! More glue doesn’t always mean a stronger joint. Only apply enough glue to evenly coat the area to be bonded when the parts are joined. Many times glue needs to be applied only to one part. Working or positioning time will vary depending on the material. Even though ZAP-A-GAP CA+ is a gap filling formula, some of it will wick into porous materials. For porous products you may have to apply more glue to get the strongest bond, it would be best to try bonding some test pieces to determine the proper amount. For modeling applications where a small fillet is desirable, bond the parts and let the glue set, then go back and create the fillet, use kicker to immediately set the glue. For critical applications test sample joints for the designed strength requirements.

    SKU: ZAPPT08
    €7.90

    IN STOCK
English
EUR (€)
Belgium
  • Select language:
    English
    German
    English
    Spanish
    French
    Italian
    Dutch
  • Select currency:
  • Select your country: